Whirlpool Washer Error Codes
Whirlpool Washer Error Codes: find your code, try the safe step, and book if it does not clear.
Whirlpool Washer Error Codes explained in plain words: what the display says, the safe thing to try first, and when to book a technician.
These codes come from Whirlpool’s Product Help page for front-load washers. Whirlpool says to clear most codes by pressing Pause or Cancel twice, then Power once. If a code remains, unplug the washer or cut power for 5 minutes, reconnect it and restart.
Codes vary by model: check your manual or the model label.
Before you try anything: switch the appliance off and unplug it, or turn off its breaker, before you touch a hose, filter or panel. Do not open the control board or electronics, and never bypass a safety switch, lock or thermostat to get past a code.
Whirlpool Washer Error Codes: what each one means
F5 E2
- What the manufacturer says: The door is not locking properly.
- One safe thing to try: Remove anything blocking the door and make sure it closes completely.
- Book a technician when: the code returns with the door clear and shut.
F7 E1
- What the manufacturer says: A motor speed sensing error.
- One safe thing to try: Check that all shipping bolts have been removed and the load is not oversized.
- Book a technician when: the code returns.
F8 E1 or LO FL
- What the manufacturer says: Low water flow is detected.
- One safe thing to try: Check that the water supply is on, both faucets are fully open and the hoses are not kinked.
- Book a technician when: the code returns once the supply is checked.
F8 E2
- What the manufacturer says: A dispenser system problem on select models.
- One safe thing to try: Check the detergent drawer or cartridge is not clogged.
- Book a technician when: it persists after cleaning the dispenser.
F9 E1
- What the manufacturer says: Drain times are longer than expected, typically over 8 minutes.
- One safe thing to try: Check the drain hose is not kinked or clogged. Whirlpool says the standpipe should be 39 to 96 inches high and suggests HE detergent.
- Book a technician when: the washer still drains slowly.
Sud or Sd
- What the manufacturer says: Too many suds.
- One safe thing to try: Use HE detergent. Whirlpool says the washer extends rinsing on its own.
- Book a technician when: suds keep returning.
Int
- What the manufacturer says: The cycle was paused or canceled.
- One safe thing to try: Press Pause or Cancel twice, then Power once.
- Book a technician when: it remains after unplugging for 5 minutes.
rL or F34
- What the manufacturer says: Items were found in the drum during Clean Washer.
- One safe thing to try: Remove the items and restart Clean Washer.
- Book a technician when: it remains.
LOC or LC
- What the manufacturer says: Control lock is on.
- One safe thing to try: Touch the Control Lock button.
- Book a technician when: never, if it clears.
dET
- What the manufacturer says: No detergent cartridge is detected on select models.
- One safe thing to try: Make sure the cartridge is seated and the drawer is fully closed.
- Book a technician when: it remains.
Other F# E# codes
- What the manufacturer says: Whirlpool lists these as other errors.
- One safe thing to try: Unplug the washer or disconnect power for 5 minutes, reconnect, reselect the cycle and press Start.
- Book a technician when: the code persists.
If the code keeps coming back
Whirlpool’s page covers front-load washers; top-load models and other brands use different lists. We repair Whirlpool washers; see our Whirlpool page and our washer repair page. When you are ready, book a visit or call (916) 582-7791. the visit is $80, and we explain the cause and your options before any repair.
Need help with whirlpool washer error codes? Book a visit or call (916) 582-7791.
Sources
Questions about whirlpool washer error codes
How do I clear a Whirlpool washer error code?+
Whirlpool says to press Pause or Cancel twice, then Power once. If it remains, unplug the washer or cut power for 5 minutes.
My Whirlpool washer shows F9 E1. What does it mean?+
Whirlpool says drain times are longer than expected, typically over 8 minutes. Check the drain hose for kinks or clogs.
Do these codes apply to my top-load Whirlpool?+
These codes come from Whirlpool's front-load washer page, so check your manual if you have a top-load model.
