GE Dishwasher Error Codes
GE Dishwasher Error Codes: find your code, try the safe step, and book if it does not clear.
GE Dishwasher Error Codes explained in plain words: what the display says, the safe thing to try first, and when to book a technician.
These codes come from GE Appliances’ support page for dishwasher error, fault and function codes. GE says disconnecting power for a minute or two can clear a code, and that lights and sounds mean different things on different models.
Codes vary by model: check your manual or the model label.
Before you try anything: switch the appliance off and unplug it, or turn off its breaker, before you touch a hose, filter or panel. Do not open the control board or electronics, and never bypass a safety switch, lock or thermostat to get past a code.
GE Dishwasher Error Codes: what each one means
C1
- What the manufacturer says: The pump out during drain exceeded 2 minutes.
- One safe thing to try: Clean the air gap, reposition the hose and run the disposer to clear it.
- Book a technician when: the code persists.
C2
- What the manufacturer says: The total pump out cycle exceeded 7 minutes.
- One safe thing to try: Press RESET to stop the beep.
- Book a technician when: it returns.
C3
- What the manufacturer says: The dishwasher will not drain.
- One safe thing to try: Turn off power at the breaker for about 30 seconds, then reset.
- Book a technician when: the problem persists.
C4
- What the manufacturer says: The machine filled twice after a power failure, due to a stuck or failed float switch, or a clogged drain or sump.
- One safe thing to try: Touch Start, then Cancel/Reset, tap the float cover to free it, and check the sump for debris.
- Book a technician when: the problem persists.
C5
- What the manufacturer says: The pump out time is too short.
- One safe thing to try: Confirm the water supply is on and rerun the cycle.
- Book a technician when: it returns.
C6
- What the manufacturer says: The water temperature is too low.
- One safe thing to try: Make sure the inlet water is at least 120 degrees F and run the nearby faucet before starting.
- Book a technician when: hot water at the tap is fine and the code returns.
C7
- What the manufacturer says: The water temperature sensor circuit is inoperative.
- One safe thing to try: Turn off power at the breaker for about 30 seconds, then reset.
- Book a technician when: the problem persists.
C8
- What the manufacturer says: The detergent cup is blocked from opening fully.
- One safe thing to try: Remove the obstruction, such as silverware or a pan, then close and latch the door.
- Book a technician when: the cup still will not open.
PF
- What the manufacturer says: A power failure occurred.
- One safe thing to try: Select the cycle and options and press Start.
- Book a technician when: it keeps happening.
Cup Open
- What the manufacturer says: The detergent cup is not closed.
- One safe thing to try: Add detergent and latch the cup closed.
- Book a technician when: it persists.
FTD or F56
- What the manufacturer says: Failure to drain.
- One safe thing to try: Check the drain hose, air gap and disposer.
- Book a technician when: it still will not drain.
H2O
- What the manufacturer says: A low water situation.
- One safe thing to try: Check the inlet hose is not kinked and the water supply is open.
- Book a technician when: it appears during the 1-Hour Wash cycle (GE says to schedule service), or it persists with a clear hose and an open supply.
999 or LEAK DETECTED
- What the manufacturer says: A possible leak. On Floor Protect models the dishwasher will not start.
- One safe thing to try: Look under the dishwasher for water. On models without Floor Protect, reset the control as GE describes.
- Book a technician when: straight away on Floor Protect models, or if you find water.
PrS
- What the manufacturer says: The pressure sensor is sending an invalid signal.
- One safe thing to try: None. GE says it is likely a harness or sensor issue.
- Book a technician when: straight away. GE recommends service.
If the code keeps coming back
GE codes vary by model, so use this as a starting point. We repair GE dishwashers; see our GE page and our dishwasher repair page. When you are ready, book a visit or call (916) 582-7791. the visit is $80, and we explain the cause and your options before any repair.
Need help with ge dishwasher error codes? Book a visit or call (916) 582-7791.
Sources
Questions about ge dishwasher error codes
How do I reset a GE dishwasher code?+
GE says disconnecting power for a minute or two can clear a code. If it remains, service is needed.
What does C1 mean on a GE dishwasher?+
GE says C1 means the pump out during drain exceeded 2 minutes. Clean the air gap, check the hose and run the disposer.
My GE dishwasher says 999. Is that a leak?+
GE says 999 is a possible leak on models with Floor Protect with Alert. Those will not start until serviced. Other models need a control reset.
